Manifold air pressure: Difference between revisions

From S4wiki
Jump to navigation Jump to search
 
(19 intermediate revisions by 2 users not shown)
Line 1: Line 1:
"MAP" sensor in this context is a misnomer. The boost pressure sensor on the S4 is actually upstream of the throttle valve. The ECU itself simulates the pressure drop over the throttle plate to synthesize a calculated MAP pressure (in conjunction with MAF and RPM data, among other things). This also means that the data coming from this pressure sensor cannot be used to run in [[speed density]] mode w/o a MAF.
==Charge pressure sender G31==

=Charge pressure sender G31=


[[Image:Charge_pressure_sender_G31.png|right|200px]]
[[Image:Charge_pressure_sender_G31.png|right|200px]]
Line 21: Line 23:
pressure is exceeded.
pressure is exceeded.


The absolute maximum pressure reading is approximately 2.559 bar absolute (22.45 psi).
The absolute maximum pressure reading is approximately 2.55996 bar absolute (22.45 psi), which should read approximately 4.76 volts.
Pressure readings that deviate more than ~500mbar from specified pressure may cause [[throttle cut]].
Pressure readings that deviate more than ~500mbar from specified pressure may cause [[throttle cut]].


The maximum pressure reading is not a function of the MAP sensor, but rather the pressure representation limit in the ECU's memory (a 16 bit, unsigned integer).


<math>0xffff/25.6 = 2559.9609375</math>
===Substitute function and self-diagnosis===

==Substitute function and self-diagnosis==
If sender G31 fails, the charge pressure is
If sender G31 fails, the charge pressure is
controlled via the characteristic curve (engine
controlled via the characteristic curve (engine
Line 31: Line 36:
deficiency of engine power.
deficiency of engine power.


===Transfer function===
==Transfer function==
The G31 is part number 078 906 051 - similar to
The G31 is part number 078 906 051 (Bosch 0 281 002 177) - similar to
[http://nyet.org/cars/info/Map_Sensor_Technical_Specification.pdf Bosch Motorsport]
[http://nyet.org/cars/info/Map_Sensor_Technical_Specification.pdf Bosch Motorsport]
[http://rb-aa.bosch.com/boaasocs/index.jsp;jsessionid=4F3BFB57CC33BB211F80A84F59148E09.sundoro?ccat_id=110&prod_id=201 0 281 002 205]
[http://rb-aa.bosch.com/boaasocs/index.jsp;jsessionid=4F3BFB57CC33BB211F80A84F59148E09.sundoro?ccat_id=110&prod_id=201 0 281 002 205]
Line 38: Line 43:
[http://www.freescale.com/files/sensors/doc/data_sheet/MPX4250A.pdf Motorola/Freescale MPX4250A].
[http://www.freescale.com/files/sensors/doc/data_sheet/MPX4250A.pdf Motorola/Freescale MPX4250A].


[[Image:BoschTransfer_small.png]]
===Bosch===

====OEM====
*0 281 002 177: 0.2?-2.5 bar (078 906 051 - Audi 2.7t)
where P1 = 0.2 bar and P2 = 2.5 bar, such that <math>V = 1.848 P + 0.03043</math>



'''Gradient and Offset Calculations'''

:<math>MINPRESSURE = 200mBar</math>
:<math>MAXPRESSURE = 2500mBar</math>
:<math>MINVOLTAGE = 0.4 Volts</math>
:<math>MAXVOLTAGE = 4.65 Volts</math>

:<math>DSLGRAD = (MAXPRESSURE - MINPRESSURE) / (MAXVOLTAGE - MINVOLTAGE) = 541.18</math>
:<math>DSLOFS = MAXPRESSURE - (DSLGRAD * MAXVOLTAGE) = -16.47</math>


From the calculations, we find the following for the stock MAP sensor (these are in accordance with the stock values in a file such as 551M):

'''DSLGRAD = 541.18'''

'''DSLOFS = -16.47'''


However, not all Bosch MAP sensors use the same transfer function. Another Bosch transfer function is shown here (type 2).

[[Image:BoschTransfer2_small.png]]

Ensure you are using the right characteristic curve to calculate the gradient and offset for the sensor.

==Bosch==
===OEM===
*0 281 002 177: 0.2-2.5 bar (078 906 051 - Audi 2.7t)
*0 281 002 399: 0.2-2.5 bar (038 906 051 B - VW Golf V TDI)
*0 281 002 399: 0.2-2.5 bar (038 906 051 B - VW Golf V TDI)
*0 281 002 401: 0.2-3.0 bar (038 906 051 C - Audi TTMKII/VW Jetta V TDI)
*0 281 002 401: 0.2-'''3.0 bar''' ('''038 906 051 C''' - Audi TTMKII/VW Jetta V TDI)
*0 281 006 060: ?.?-4.0 bar (03K 906 051)
*0 281 006 060: 0.5-'''4.0 bar''' ('''03K 906 051''') (uses characteristic curve type 2)
*0 261 230 294: 0.5-'''3.5 bar''' ('''31303974 or 31355462''') - Volvo D3,D4,D5 2012+ (uses characteristic curve type 2)


====No temp sensor====
===No temp sensor===
*0 281 002 487: 0.2-2.5 bar (one mounting hole)
*0 281 002 487: 0.2-2.5 bar (one mounting hole)


====With temp sensor====
===With temp sensor===
*0 281 002 399: 0.2-2.5 bar
*0 281 002 399: 0.2-2.5 bar
*0 281 002 205: 0.2-2.5 bar
*0 281 002 205: 0.2-2.5 bar
Line 56: Line 92:
*0 261 230 105: 0.2-3.0 bar (one mounting hole)
*0 261 230 105: 0.2-3.0 bar (one mounting hole)
*0 281 002 244: 0.5-3.5 bar
*0 281 002 244: 0.5-3.5 bar
*0 281 002 456: 0.5-3.5 bar (one mounting hole)
*0 281 002 456: 0.5-3.5 bar (one mounting hole) (uses characteristic curve type 2)
*0 281 002 316: 0.5-4.0 bar
*0 281 002 316: 0.5-4.0 bar
*0 281 002 576: 0.5-5.0 bar (one mounting hole)
*0 281 002 576: 0.5-4.0 bar (one mounting hole)
*0 261 230 105: 0.2-3.0 bar (one mounting hole)
*0 261 230 105: 0.2-3.0 bar (one mounting hole)


===Motorola===
==Motorola==
====MPX4250A====
===MPX4250A===
VOUT = VS (P × 0.004 - 0.04)
VOUT = VS (P × 0.004 - 0.04)
± (Pressure Error × Temp. Factor × 0.004 × VS)
± (Pressure Error × Temp. Factor × 0.004 × VS)
Line 69: Line 105:
[[Image:MPX4250A-transfer-function.png]]
[[Image:MPX4250A-transfer-function.png]]


==References==
=References=
* [http://forums.audiworld.com/s4/msgs/2271731.phtml AW discussion] on MAP sensor function
* [http://forums.audiworld.com/s4/msgs/2271731.phtml AW discussion] on MAP sensor function

Latest revision as of 22:17, 6 November 2019

"MAP" sensor in this context is a misnomer. The boost pressure sensor on the S4 is actually upstream of the throttle valve. The ECU itself simulates the pressure drop over the throttle plate to synthesize a calculated MAP pressure (in conjunction with MAF and RPM data, among other things). This also means that the data coming from this pressure sensor cannot be used to run in speed density mode w/o a MAF.

Charge pressure sender G31

Charge pressure sender G31.png

The charge pressure sender is located upstream of the throttle valve control part.

The Motronic supplies the sender with a voltage of 5 volts and earth. The signal which the sender generates is a pressure-proportional voltage ranging from 0 to 5 volts.

At atmospheric pressure (14.7 psi or 1.01 bar at sea-level), the voltage is approx. 1.88 volts.

The signal is used for charge pressure control.

The Motronic also needs information on charge pressure so that it can take countermeasures if the maximum permissible pressure is exceeded.

The absolute maximum pressure reading is approximately 2.55996 bar absolute (22.45 psi), which should read approximately 4.76 volts. Pressure readings that deviate more than ~500mbar from specified pressure may cause throttle cut.

The maximum pressure reading is not a function of the MAP sensor, but rather the pressure representation limit in the ECU's memory (a 16 bit, unsigned integer).

Substitute function and self-diagnosis

If sender G31 fails, the charge pressure is controlled via the characteristic curve (engine speed-dependent). This will result in a deficiency of engine power.

Transfer function

The G31 is part number 078 906 051 (Bosch 0 281 002 177) - similar to Bosch Motorsport 0 281 002 205 or Motorola/Freescale MPX4250A.

BoschTransfer small.png

where P1 = 0.2 bar and P2 = 2.5 bar, such that


Gradient and Offset Calculations


From the calculations, we find the following for the stock MAP sensor (these are in accordance with the stock values in a file such as 551M):

DSLGRAD = 541.18

DSLOFS = -16.47


However, not all Bosch MAP sensors use the same transfer function. Another Bosch transfer function is shown here (type 2).

BoschTransfer2 small.png

Ensure you are using the right characteristic curve to calculate the gradient and offset for the sensor.

Bosch

OEM

  • 0 281 002 177: 0.2-2.5 bar (078 906 051 - Audi 2.7t)
  • 0 281 002 399: 0.2-2.5 bar (038 906 051 B - VW Golf V TDI)
  • 0 281 002 401: 0.2-3.0 bar (038 906 051 C - Audi TTMKII/VW Jetta V TDI)
  • 0 281 006 060: 0.5-4.0 bar (03K 906 051) (uses characteristic curve type 2)
  • 0 261 230 294: 0.5-3.5 bar (31303974 or 31355462) - Volvo D3,D4,D5 2012+ (uses characteristic curve type 2)

No temp sensor

  • 0 281 002 487: 0.2-2.5 bar (one mounting hole)

With temp sensor

  • 0 281 002 399: 0.2-2.5 bar
  • 0 281 002 205: 0.2-2.5 bar
  • 0 261 230 042: 0.2-2.5 bar (one mounting hole)
  • 0 281 002 573: 0.2-2.5 bar (no mounting holes)
  • 0 281 002 437: 0.2-3.0 bar (one mounting hole)
  • 0 261 230 105: 0.2-3.0 bar (one mounting hole)
  • 0 281 002 244: 0.5-3.5 bar
  • 0 281 002 456: 0.5-3.5 bar (one mounting hole) (uses characteristic curve type 2)
  • 0 281 002 316: 0.5-4.0 bar
  • 0 281 002 576: 0.5-4.0 bar (one mounting hole)
  • 0 261 230 105: 0.2-3.0 bar (one mounting hole)

Motorola

MPX4250A

VOUT = VS (P × 0.004 - 0.04)
± (Pressure Error × Temp. Factor × 0.004 × VS)
VS = 5.1 V ± 0.25 VDC

MPX4250A-transfer-function.png

References