Fuel injectors

From S4wiki
Revision as of 01:56, 20 January 2011 by Nyet (talk | contribs) (→‎Flow)
Jump to navigation Jump to search

Flow

Injector Rated flow 2 bar 3 bar 3.5 bar 4 bar 5 bar Spray pattern Length Connector
Siemens S4 33#@4bar 349cc/33# 390cc/37# 52mm Jetronic
Bosch Bluetop 36#@3bar 309cc/29# 380cc/36# 422cc/40# 490cc/47#
RS4 46#@4bar 480cc/46# 538cc/51# 15° dual 37mm
Greentop 42#@3bar 475cc/45# 550cc/52# 615cc/59# 15° single 64mm
Green Giant (Volvo) 42#@3bar 450cc/43# 520cc/50# 560cc/55# 15° dual
EV14 0280158117 532cc@2.7bar 550cc/52# 635cc/60# 15° dual 52mm USCAR
750cc[1]
Delphi 37#@3bar 391cc/37# 462cc/43# Jetronic
38#@3bar 399cc/38# 462cc/44#
42#@3bar 441cc/42# 515cc/49#
50#@3bar 525cc/50# 609cc/58# 22.4° wide
Siemens Deka IV ('03 SRT4) 41#?@3bar 452cc/41#? 524cc/47#? Dual? 52mm USCAR
Deka IV ('04 SRT4) 45#@3bar 475cc/45# 546cc/52# Dual?
Deka ID (3172) 55#@3bar 472cc/45# 600cc/57# 624cc/59.5# 667cc/63.5# 746cc/71# 15° single 2 1/2" Jetronic
Deka IV (1496) 60#@3bar 514cc/49# 630cc/60# 727cc/70# 30.0° wide
Genesis 415cc@3bar 415cc/39# 483cc/46# Dual 52mm
430cc@3bar 430cc/41# 494cc/47# Dual USCAR
550cc@3bar 550cc/52# 580cc/55# 635cc/60# Dual
  • Bold denotes the rated pressure.
  • Length is o-ring center to center.

Spacers

Bosch EV14 injector sizes.jpg

2 1/2" (64mm) injectors require 12mm (7/16") spacers when using the S4 intake manifold and fuel rail. If you are using an RS4 fuel rail you will need a 1" spacer!

mm inches Bosch (not c-to-c) S4 rail spacer RS4 rail spacer
37mm 1 1/2" 33.60mm N/A none
52mm 2 1/16" 48.65mm none 15mm (9/16")
64mm 2 1/2" 60.65mm 12mm (7/16") 27mm (1")

Note that Bosch's EV14 length specs are not o-ring center to center


Adaptors

Connector Shape Bosch A.K.A.
Jetronic Rectangle Design II EV1/Minitimer
USCAR Oval Design III EV6/EV14

Injectors are male, harness is female, so to use a USCAR/EV6/EV14 injector on a Minitimer/Jetronic/EV1 car, you need a USCAR (female) to Jetronic (male) adapter.[2][3]


Conversions

  • 1 lb/hr gasoline = 10.5 cc/min (@720 kg/m3) (1 (pound / hr)) / (720 (kg / (m^3)))
  • Density of typical test fluid = 760 - 770 kg/m3
    1 lb/hr = 9.81 - 9.95 cc/min
  • Density of n-heptane = 685 kg/m3
    1 lb/hr = 11.0 cc/min
  • 3 bar = 43.5 psi
  • 4 bar = 58.0 psi
  • 5 bar = 72.5 psi
  • RC Engineering's online calculator

Instrument cluster

If you change fuel injectors, your instrument cluster will estimate your fuel consumption incorrectly. Use VAG-COM to adjust it by going to Instrument cluster (17) -> Adaptation (10) -> Channel (03).[4]

Unfortunately, you can only set it to a maximum of 115%. Default is 100%.

If you have access to ME7.x tuning tools, you can completely fix cluster consumption by adjusting the KVB 1x1.

References

Notes