==General information==

A mass air flow (or MAF) sensor placed just before the intake manifold measures the instantaneous rate of air entering the combustion chamber. This is done using a thin wire or film suspended in the air stream.

===Hot wire MAF===
A hot wire MAF is composed of a thermistor wire and an ammeter. Since the MAF wire is a "positive k" thermistor, the hotter it gets, the higher its resistance. The colder it gets, the lower its resistance, and the more current that passes through the wire. However, the more current flowing through the wire, the hotter it gets (similar to an electric heater). This sets an upper stable limit of current, since as the resistance of the wire increases, the less current that flows through it. This "stable" point changes depending on how much air is flowing past the wire, providing cooling. The more air flowing past the wire, the more current the wire can allow through before it heats up enough to offset the current. Therefore, at any given time, the amount of air flowing through the MAF is proportional to the amount of current flowing through the wire in the sensor.

===Hot film MAF===
[[Image:Hot_film_maf.png|right|400px]]
A hot film MAF is comprised of a diaphragm with a heating zone and two symmetrically arranged temperature sensors on either side of the heating zone. A control circuit maintains the heating zone at a constant overtemperature above ambient such that the downstream sensor reads a lower (but constant) temperature. The more air that blows past the upstream sensor, the cooler it is when compared to the downstream sensor. Thus, the difference in temperature (ΔT) between the upstream and downstream temperature sensor is proportional to the amount (and direction) of air mass flowing over the membrane. A thin film MAF can also detect a reverse flow of air, which may happen during high load factors. Reverse flow pulses from the pistion generate waves in the air upstream of the throttle body, and should not be allowed to affect the meter's readings.

==S4 specific information==
The B5 S4's Bosch Motronic ME7.1 ECU uses a mass air flow based fuel injection system. During [[open loop]] (engine warm-up and wide open throttle) operation, the MAF tells the ECU how much fuel to deliver to keep the [[air fuel ratio]] at an optimal level (also known as [[stoichiometric]]).

Unlike wideband O2 sensor equipped cars, the ME7.1's narrow band 02 readings are ignored during open loop operation. The [[O2 sensor]]s (along with MAF readings) are used to determine fueling only during [[closed loop]] operation (idle and partial throttle). Note that since MAF readings are also used during closed loop operation, [[long term fuel trim]]s (or LTFTs) may be affected by faulty or incorrectly tuned MAF setups, including the use of [[blow off valve]]s (or BOVs).

===Temperature (IAT) effect on MAF readings===

Because of their design, both the Bosch and Hitachi MAF correct for ambient temperature, so the ECU does not use the IAT sensor in its load calculations.

Both types of thin film MAF keep the heating element at a constant overtemperature above ambient, so the ΔT between the upstream and the downstream sensor will always give a "cooling capacity" of the mass of air passing over the film. By holding the overtemperature constant, the "cooling capacity" is linear with the air mass passing over the film, regardless of IAT.

===IAT effect on timing and fueling===

However, IAT does play a role in adjusting the base timing and fueling maps. Unfortunately, those [[Lemmiwinks#EGT_and_IAT_effects_on_fueling | adjustments]] are done before any correction factor (ignition retard) that comes from the [[knock control]] function, so IAT related timing adjustment values are not visible to tools like [[VAGCOM]] or [[ECUx]]. In general, the higher the IAT is above approximately 50°C (~120°F), the more timing will be pulled and the more fuel will be added.

===Bosch vs. Hitachi===

B5 S4s came with [[Generations | two different types]] of MAF sensors - Bosch (078 906 461B) and Hitachi (06C 133 471A); both are film-type MAFs. Each has totally different signal characteristics and are not compatible, even if properly rewired. [[A-Box]]/[[B-Box]] cars (MY2000) came with Bosch MAFs. [[H-Box]]/[[J-Box]] (MY2001), [[M-Box]]/[[L-Box]] (MY2001.5), and [[T-Box]]/[[AA-Box]] (MY2002) cars came with Hitachi MAFs.

{| class="wikitable"
! || colspan=2 | A-Box/B-Box/S8/[[RS4]] aka Bosch || colspan=2 | H/J/M/L/T/AA-Box aka Hitachi
|-
! pin || color || wire || color || wire
|-
| 1 || blank/unused || none || style="background:violet; color:grey"|violet/grey || +5V
|-
| 2 || style="background:green; color:yellow"|green/yellow || +12V (ign/bat) ||style="background:green; color:yellow"|green/yellow || +12V (ign/bat)
|-
| 3 || style="background:black; color:lightgreen"|black/green || ground || style="background:black; color:lightgreen"|black/green || ground
|-
| 4 || style="background:violet; color:grey"|violet/grey || +5V || style="background:green"|green || signal
|-
| 5 || style="background:green"|green || signal || blank/unused || none
|}

In order to switch between the two, you must have the correct version of ECU. Changing from one "box" to another is as easy as unplugging one ECU and plugging in another. Some tuners offer "flash" upgrades where an ECU can be reprogrammed via the [[OBD-II]] port. However, changing ECU boxes may also require a [[cluster recode]].

==Logging/tuning/trouble shooting==

===Signal conditioning===
[[Image:MAF_V_vs_g_per_sec.png|right|300px]]
* For the Hitachi MAF
**0-0.5V means negative air flow?
**0.5V is zero air flow?
**5.0V is maximum reading.
**the ECU reads roughly <math>16*(V-0.5)^2</math> g/sec. Although the voltage to grams/sec conversion is independant of IAT, it appears as though the ECU has a correction factor that goes up with RPM.
* can "tweak" measured maf values by using a piggyback [http://www.splitsec.com/products/conditioner.htm signal conditioner]
* difference in polarity between bosch/hitachi?
* Bosch is 0V -> max air flow, 4.5V -> zero air flow, 4.5V-5V -> negative air flow?

===MAF housing diameter===
* MAF signal has an absolute top end reading of 5 volts. So have to scale MAF if we want more HP (since more HP means more air will be passing through MAF).
*To keep the signal under 5 volts for the maximum air flow, we have to make the diameter larger. This will make the signal smaller for a given air mass flow.
* For a given mass air flow:
** air velocity goes down with cross sectional area
** cooling capacity goes down with cross sectional area or diameter?
** voltage goes down with diameter?
** MAF reading therefore down with square of diameter and with crossectional area
* more air means we need more fuel - larger injectors, higher pressure FPR
* how to determine MAF housing diameter vs injector size and fuel pressure (fuel flow).

=== Effect on Velocity ===

Velocity is one way to approximate the maximum airflow that can be measured by a sensor, because it is independent of the housing's cross sectional area.

A strong S4 running stock K03s, MAF, and fueling uses approximately 260 g/sec of air.

To calculate velocity, we convert the g/sec into <math>m^3/sec</math> (volume of air per second) by dividing by 1225 <math>g/m^3</math> (density of air at sea level).

We then divide by the cross sectional area of the housing (<math>(D\pi/2)^2</math>).

So we get [http://www.google.com/search?q=260%2F1225+m%5E3%2Fsec+%2F%28pi+*+%28%2873%2F2%29mm%29%5E2%29++in+mph%3D&btnG=Search <math>(((260/1 225) (m^3)) / sec) / (pi * (((73 / 2) * mm)^2)) = 113.437141 mph</math>]

=== Effect on Airflow ===

<math>X = \pi (A/2)^2</math>

where (A) is the new MAF Housing diameter in mm. (ex.: 88mm, 90mm, etc.)

<math>Y = \pi (73/2)^2</math>

73mm being the stock MAF Housing size in mm.

Increase in MAF (g/s) in % = <math>((D^2/73^2)-1) 100</math>

{| class="wikitable" style="background:lightgrey"
|+ Various stock MAF housing diameters
! ||MAF|| Diameter || Max airflow || Velocity
|-
|Stock ||S4 ||73mm||220 g/sec||96 mph
|-
|Stock ||RS4 ||83mm||320 g/sec||108 mph
|-
|Chipped ||S4 ||73mm||260 g/sec||113 mph
|-
|VAGCOM limit||RS4||83mm||364.08 g/sec||122 mph
|-
|Stage2+ ||S4 ||73mm||320 g/sec||140 mph
|-
|5V at sensor||S4 ||73mm||364? g/sec||159 mph
|-
|5V at sensor||RS4||83mm||499 g/sec||168 mph
|}

* VAGCOM limit seems to be 318ish on M/T-box, 335ish for M-box, high 320s for A box.
* Sensor value absolute maximums are 364.08 on VAGCOM and 499 on ECUx.
* Note that some programs scale g/sec readings, so what ECUx/VAG-COM reports can't always be trusted.

=== Using the maximum velocity ===

As you can see, the maximum velocity measured by both the Hitachi and Bosch sensors is approximately 160mph. We can use this value to determine what size housing we need to measure a given maximum amount of air mass with a given sensor.

{| class="wikitable" style="background:lightgrey"
|+ Various modded MAF housing diameters
!MAF || Diameter || Velocity || Measured g/sec || True g/sec
|-
|D-Flo ||83mm || rowspan="5" | 160mph || rowspan="5" | 367 || 474
|-
|AWE || 84mm* || 486
|-
|ASP || 85mm || 497
|-
|Custom|| 88mm || 533
|-
|ASP || 90mm || 558
|}

*AWE actual dimensions are 77mm (inlet) to 100mm at sensor. It reads equivalent to an 82mm-84mm MAF

=== Change in airflow relative to diameter ===

Another way to determine how big a housing to use for a MAF value is by simply using percentages.

{| class="wikitable" style="background:lightgrey"
|+ Various modded MAF housing diameters
!MAF || Diameter || Deviation || Measured g/sec || True g/sec
|-
|D-Flo ||83mm || +29.3% || rowspan="5" | 364 || 471
|-
|AWE ||84mm || +30% || 473
|-
|ASP ||85mm || +35.6% || 493
|-
|Custom||88mm || +45.3% || 528
|-
|ASP ||90mm || +52.0% || 553
|}

===MAF and fueling===
* how lemmi fueling (pri/second/accell/decel)
** affects open loop fueling (MAF vs injector duty)
** affects closed loop fueling (LTFTs)
** see also [[Lemmiwinks]].

===Bad MAF===
* Unplugging the MAF will result in the ECU thinking it is broken. Some think this will prevent the ECU from ever going open loop, some think that the ECU can go open loop, but the MAF signal is simply ignored.
* The Audi 2.7t [http://nyet.org/cars/info/Audi_S4_engine_english.pdf self study guide] (page 50) says "If the air mass meter fails, the air mass is calculated on the basis of a [[characteristic curve]] (throttle valve angle and engine speed)"
* Is the [[MAP]] used in "characteristic curve" calculations?
* If so, what does the ECU do in the case where it thinks the MAP is dead?

[[Category:Tuning]]

Mass air flow

2007-03-26T21:10:50Z

Pansgor: /* Change in airflow relative to diameter */

==General information==

A mass air flow (or MAF) sensor placed just before the intake manifold measures the instantaneous rate of air entering the combustion chamber. This is done using a thin wire or film suspended in the air stream.

===Hot wire MAF===
A hot wire MAF is composed of a thermistor wire and an ammeter. Since the MAF wire is a "positive k" thermistor, the hotter it gets, the higher its resistance. The colder it gets, the lower its resistance, and the more current that passes through the wire. However, the more current flowing through the wire, the hotter it gets (similar to an electric heater). This sets an upper stable limit of current, since as the resistance of the wire increases, the less current that flows through it. This "stable" point changes depending on how much air is flowing past the wire, providing cooling. The more air flowing past the wire, the more current the wire can allow through before it heats up enough to offset the current. Therefore, at any given time, the amount of air flowing through the MAF is proportional to the amount of current flowing through the wire in the sensor.

===Hot film MAF===
[[Image:Hot_film_maf.png|right|400px]]
A hot film MAF is comprised of a diaphragm with a heating zone and two symmetrically arranged temperature sensors on either side of the heating zone. A control circuit maintains the heating zone at a constant overtemperature above ambient such that the downstream sensor reads a lower (but constant) temperature. The more air that blows past the upstream sensor, the cooler it is when compared to the downstream sensor. Thus, the difference in temperature (ΔT) between the upstream and downstream temperature sensor is proportional to the amount (and direction) of air mass flowing over the membrane. A thin film MAF can also detect a reverse flow of air, which may happen during high load factors. Reverse flow pulses from the pistion generate waves in the air upstream of the throttle body, and should not be allowed to affect the meter's readings.

==S4 specific information==
The B5 S4's Bosch Motronic ME7.1 ECU uses a mass air flow based fuel injection system. During [[open loop]] (engine warm-up and wide open throttle) operation, the MAF tells the ECU how much fuel to deliver to keep the [[air fuel ratio]] at an optimal level (also known as [[stoichiometric]]).

Unlike wideband O2 sensor equipped cars, the ME7.1's narrow band 02 readings are ignored during open loop operation. The [[O2 sensor]]s (along with MAF readings) are used to determine fueling only during [[closed loop]] operation (idle and partial throttle). Note that since MAF readings are also used during closed loop operation, [[long term fuel trim]]s (or LTFTs) may be affected by faulty or incorrectly tuned MAF setups, including the use of [[blow off valve]]s (or BOVs).

===Temperature (IAT) effect on MAF readings===

Because of their design, both the Bosch and Hitachi MAF correct for ambient temperature, so the ECU does not use the IAT sensor in its load calculations.

Both types of thin film MAF keep the heating element at a constant overtemperature above ambient, so the ΔT between the upstream and the downstream sensor will always give a "cooling capacity" of the mass of air passing over the film. By holding the overtemperature constant, the "cooling capacity" is linear with the air mass passing over the film, regardless of IAT.

===IAT effect on timing and fueling===

However, IAT does play a role in adjusting the base timing and fueling maps. Unfortunately, those [[Lemmiwinks#EGT_and_IAT_effects_on_fueling | adjustments]] are done before any correction factor (ignition retard) that comes from the [[knock control]] function, so IAT related timing adjustment values are not visible to tools like [[VAGCOM]] or [[ECUx]]. In general, the higher the IAT is above approximately 50°C (~120°F), the more timing will be pulled and the more fuel will be added.

===Bosch vs. Hitachi===

B5 S4s came with [[Generations | two different types]] of MAF sensors - Bosch (078 906 461B) and Hitachi (06C 133 471A); both are film-type MAFs. Each has totally different signal characteristics and are not compatible, even if properly rewired. [[A-Box]]/[[B-Box]] cars (MY2000) came with Bosch MAFs. [[H-Box]]/[[J-Box]] (MY2001), [[M-Box]]/[[L-Box]] (MY2001.5), and [[T-Box]]/[[AA-Box]] (MY2002) cars came with Hitachi MAFs.

{| class="wikitable"
! || colspan=2 | A-Box/B-Box/S8/[[RS4]] aka Bosch || colspan=2 | H/J/M/L/T/AA-Box aka Hitachi
|-
! pin || color || wire || color || wire
|-
| 1 || blank/unused || none || style="background:violet; color:grey"|violet/grey || +5V
|-
| 2 || style="background:green; color:yellow"|green/yellow || +12V (ign/bat) ||style="background:green; color:yellow"|green/yellow || +12V (ign/bat)
|-
| 3 || style="background:black; color:lightgreen"|black/green || ground || style="background:black; color:lightgreen"|black/green || ground
|-
| 4 || style="background:violet; color:grey"|violet/grey || +5V || style="background:green"|green || signal
|-
| 5 || style="background:green"|green || signal || blank/unused || none
|}

In order to switch between the two, you must have the correct version of ECU. Changing from one "box" to another is as easy as unplugging one ECU and plugging in another. Some tuners offer "flash" upgrades where an ECU can be reprogrammed via the [[OBD-II]] port. However, changing ECU boxes may also require a [[cluster recode]].

==Logging/tuning/trouble shooting==

===Signal conditioning===
[[Image:MAF_V_vs_g_per_sec.png|right|300px]]
* For the Hitachi MAF
**0-0.5V means negative air flow?
**0.5V is zero air flow?
**5.0V is maximum reading.
**the ECU reads roughly <math>16*(V-0.5)^2</math> g/sec. Although the voltage to grams/sec conversion is independant of IAT, it appears as though the ECU has a correction factor that goes up with RPM.
* can "tweak" measured maf values by using a piggyback [http://www.splitsec.com/products/conditioner.htm signal conditioner]
* difference in polarity between bosch/hitachi?
* Bosch is 0V -> max air flow, 4.5V -> zero air flow, 4.5V-5V -> negative air flow?

===MAF housing diameter===
* MAF signal has an absolute top end reading of 5 volts. So have to scale MAF if we want more HP (since more HP means more air will be passing through MAF).
*To keep the signal under 5 volts for the maximum air flow, we have to make the diameter larger. This will make the signal smaller for a given air mass flow.
* For a given mass air flow:
** air velocity goes down with cross sectional area
** cooling capacity goes down with cross sectional area or diameter?
** voltage goes down with diameter?
** MAF reading therefore down with square of diameter and with crossectional area
* more air means we need more fuel - larger injectors, higher pressure FPR
* how to determine MAF housing diameter vs injector size and fuel pressure (fuel flow).

=== Effect on Velocity ===

Velocity is one way to approximate the maximum airflow that can be measured by a sensor, because it is independent of the housing's cross sectional area.

A strong S4 running stock K03s, MAF, and fueling uses approximately 260 g/sec of air.

To calculate velocity, we convert the g/sec into <math>m^3/sec</math> (volume of air per second) by dividing by 1225 <math>g/m^3</math> (density of air at sea level).

We then divide by the cross sectional area of the housing (<math>(D\pi/2)^2</math>).

So we get [http://www.google.com/search?q=260%2F1225+m%5E3%2Fsec+%2F%28pi+*+%28%2873%2F2%29mm%29%5E2%29++in+mph%3D&btnG=Search <math>(((260/1 225) (m^3)) / sec) / (pi * (((73 / 2) * mm)^2)) = 113.437141 mph</math>]

=== Effect on Airflow ===

<math>X = \pi (A/2)^2</math>

where (A) is the new MAF Housing diameter in mm. (ex.: 88mm, 90mm, etc.)

<math>Y = \pi (73/2)^2</math>

73mm being the stock MAF Housing size in mm.

Increase in MAF (g/s) in % = <math>((D^2/73^2)-1) 100</math>

{| class="wikitable" style="background:lightgrey"
|+ Various stock MAF housing diameters
! ||MAF|| Diameter || Max airflow || Velocity
|-
|Stock ||S4 ||73mm||220 g/sec||96 mph
|-
|Stock ||RS4 ||83mm||320 g/sec||108 mph
|-
|Chipped ||S4 ||73mm||260 g/sec||113 mph
|-
|VAGCOM limit||RS4||83mm||364.08 g/sec||122 mph
|-
|Stage2+ ||S4 ||73mm||320 g/sec||140 mph
|-
|5V at sensor||S4 ||73mm||364? g/sec||159 mph
|-
|5V at sensor||RS4||83mm||499 g/sec||168 mph
|}

* VAGCOM limit seems to be 318ish on M/T-box, 335ish for M-box, high 320s for A box.
* Sensor value absolute maximums are 364.08 on VAGCOM and 499 on ECUx.
* Note that some programs scale g/sec readings, so what ECUx/VAG-COM reports can't always be trusted.

=== Using the maximum velocity ===

As you can see, the maximum velocity measured by both the Hitachi and Bosch sensors is approximately 160mph. We can use this value to determine what size housing we need to measure a given maximum amount of air mass with a given sensor.

{| class="wikitable" style="background:lightgrey"
|+ Various modded MAF housing diameters
!MAF || Diameter || Velocity || Measured g/sec || True g/sec
|-
|D-Flo ||83mm || rowspan="5" | 160mph ||
|-
|AWE || 84mm* ||
|-
|ASP || 85mm ||
|-
|Custom|| 88mm ||
|-
|ASP || 90mm ||
|}

*AWE actual dimensions are 77mm (inlet) to 100mm at sensor. It reads equivalent to an 82mm-84mm MAF

=== Change in airflow relative to diameter ===

Another way to determine how big a housing to use for a MAF value is by simply using percentages.

{| class="wikitable" style="background:lightgrey"
|+ Various modded MAF housing diameters
!MAF || Diameter || Deviation || Measured g/sec || True g/sec
|-
|D-Flo ||83mm || +29.3% || rowspan="5" | 364 || 471
|-
|AWE ||84mm || +30% || 473
|-
|ASP ||85mm || +35.6% || 493
|-
|Custom||88mm || +45.3% || 528
|-
|ASP ||90mm || +52.0% || 553
|}

===MAF and fueling===
* how lemmi fueling (pri/second/accell/decel)
** affects open loop fueling (MAF vs injector duty)
** affects closed loop fueling (LTFTs)
** see also [[Lemmiwinks]].

===Bad MAF===
* Unplugging the MAF will result in the ECU thinking it is broken. Some think this will prevent the ECU from ever going open loop, some think that the ECU can go open loop, but the MAF signal is simply ignored.
* The Audi 2.7t [http://nyet.org/cars/info/Audi_S4_engine_english.pdf self study guide] (page 50) says "If the air mass meter fails, the air mass is calculated on the basis of a [[characteristic curve]] (throttle valve angle and engine speed)"
* Is the [[MAP]] used in "characteristic curve" calculations?
* If so, what does the ECU do in the case where it thinks the MAP is dead?

[[Category:Tuning]]

Mass air flow

2007-03-26T21:10:42Z

Pansgor: /* Change in airflow relative to diameter */

==General information==

A mass air flow (or MAF) sensor placed just before the intake manifold measures the instantaneous rate of air entering the combustion chamber. This is done using a thin wire or film suspended in the air stream.

===Hot wire MAF===
A hot wire MAF is composed of a thermistor wire and an ammeter. Since the MAF wire is a "positive k" thermistor, the hotter it gets, the higher its resistance. The colder it gets, the lower its resistance, and the more current that passes through the wire. However, the more current flowing through the wire, the hotter it gets (similar to an electric heater). This sets an upper stable limit of current, since as the resistance of the wire increases, the less current that flows through it. This "stable" point changes depending on how much air is flowing past the wire, providing cooling. The more air flowing past the wire, the more current the wire can allow through before it heats up enough to offset the current. Therefore, at any given time, the amount of air flowing through the MAF is proportional to the amount of current flowing through the wire in the sensor.

===Hot film MAF===
[[Image:Hot_film_maf.png|right|400px]]
A hot film MAF is comprised of a diaphragm with a heating zone and two symmetrically arranged temperature sensors on either side of the heating zone. A control circuit maintains the heating zone at a constant overtemperature above ambient such that the downstream sensor reads a lower (but constant) temperature. The more air that blows past the upstream sensor, the cooler it is when compared to the downstream sensor. Thus, the difference in temperature (ΔT) between the upstream and downstream temperature sensor is proportional to the amount (and direction) of air mass flowing over the membrane. A thin film MAF can also detect a reverse flow of air, which may happen during high load factors. Reverse flow pulses from the pistion generate waves in the air upstream of the throttle body, and should not be allowed to affect the meter's readings.

==S4 specific information==
The B5 S4's Bosch Motronic ME7.1 ECU uses a mass air flow based fuel injection system. During [[open loop]] (engine warm-up and wide open throttle) operation, the MAF tells the ECU how much fuel to deliver to keep the [[air fuel ratio]] at an optimal level (also known as [[stoichiometric]]).

Unlike wideband O2 sensor equipped cars, the ME7.1's narrow band 02 readings are ignored during open loop operation. The [[O2 sensor]]s (along with MAF readings) are used to determine fueling only during [[closed loop]] operation (idle and partial throttle). Note that since MAF readings are also used during closed loop operation, [[long term fuel trim]]s (or LTFTs) may be affected by faulty or incorrectly tuned MAF setups, including the use of [[blow off valve]]s (or BOVs).

===Temperature (IAT) effect on MAF readings===

Because of their design, both the Bosch and Hitachi MAF correct for ambient temperature, so the ECU does not use the IAT sensor in its load calculations.

Both types of thin film MAF keep the heating element at a constant overtemperature above ambient, so the ΔT between the upstream and the downstream sensor will always give a "cooling capacity" of the mass of air passing over the film. By holding the overtemperature constant, the "cooling capacity" is linear with the air mass passing over the film, regardless of IAT.

===IAT effect on timing and fueling===

However, IAT does play a role in adjusting the base timing and fueling maps. Unfortunately, those [[Lemmiwinks#EGT_and_IAT_effects_on_fueling | adjustments]] are done before any correction factor (ignition retard) that comes from the [[knock control]] function, so IAT related timing adjustment values are not visible to tools like [[VAGCOM]] or [[ECUx]]. In general, the higher the IAT is above approximately 50°C (~120°F), the more timing will be pulled and the more fuel will be added.

===Bosch vs. Hitachi===

B5 S4s came with [[Generations | two different types]] of MAF sensors - Bosch (078 906 461B) and Hitachi (06C 133 471A); both are film-type MAFs. Each has totally different signal characteristics and are not compatible, even if properly rewired. [[A-Box]]/[[B-Box]] cars (MY2000) came with Bosch MAFs. [[H-Box]]/[[J-Box]] (MY2001), [[M-Box]]/[[L-Box]] (MY2001.5), and [[T-Box]]/[[AA-Box]] (MY2002) cars came with Hitachi MAFs.

{| class="wikitable"
! || colspan=2 | A-Box/B-Box/S8/[[RS4]] aka Bosch || colspan=2 | H/J/M/L/T/AA-Box aka Hitachi
|-
! pin || color || wire || color || wire
|-
| 1 || blank/unused || none || style="background:violet; color:grey"|violet/grey || +5V
|-
| 2 || style="background:green; color:yellow"|green/yellow || +12V (ign/bat) ||style="background:green; color:yellow"|green/yellow || +12V (ign/bat)
|-
| 3 || style="background:black; color:lightgreen"|black/green || ground || style="background:black; color:lightgreen"|black/green || ground
|-
| 4 || style="background:violet; color:grey"|violet/grey || +5V || style="background:green"|green || signal
|-
| 5 || style="background:green"|green || signal || blank/unused || none
|}

In order to switch between the two, you must have the correct version of ECU. Changing from one "box" to another is as easy as unplugging one ECU and plugging in another. Some tuners offer "flash" upgrades where an ECU can be reprogrammed via the [[OBD-II]] port. However, changing ECU boxes may also require a [[cluster recode]].

==Logging/tuning/trouble shooting==

===Signal conditioning===
[[Image:MAF_V_vs_g_per_sec.png|right|300px]]
* For the Hitachi MAF
**0-0.5V means negative air flow?
**0.5V is zero air flow?
**5.0V is maximum reading.
**the ECU reads roughly <math>16*(V-0.5)^2</math> g/sec. Although the voltage to grams/sec conversion is independant of IAT, it appears as though the ECU has a correction factor that goes up with RPM.
* can "tweak" measured maf values by using a piggyback [http://www.splitsec.com/products/conditioner.htm signal conditioner]
* difference in polarity between bosch/hitachi?
* Bosch is 0V -> max air flow, 4.5V -> zero air flow, 4.5V-5V -> negative air flow?

===MAF housing diameter===
* MAF signal has an absolute top end reading of 5 volts. So have to scale MAF if we want more HP (since more HP means more air will be passing through MAF).
*To keep the signal under 5 volts for the maximum air flow, we have to make the diameter larger. This will make the signal smaller for a given air mass flow.
* For a given mass air flow:
** air velocity goes down with cross sectional area
** cooling capacity goes down with cross sectional area or diameter?
** voltage goes down with diameter?
** MAF reading therefore down with square of diameter and with crossectional area
* more air means we need more fuel - larger injectors, higher pressure FPR
* how to determine MAF housing diameter vs injector size and fuel pressure (fuel flow).

=== Effect on Velocity ===

Velocity is one way to approximate the maximum airflow that can be measured by a sensor, because it is independent of the housing's cross sectional area.

A strong S4 running stock K03s, MAF, and fueling uses approximately 260 g/sec of air.

To calculate velocity, we convert the g/sec into <math>m^3/sec</math> (volume of air per second) by dividing by 1225 <math>g/m^3</math> (density of air at sea level).

We then divide by the cross sectional area of the housing (<math>(D\pi/2)^2</math>).

So we get [http://www.google.com/search?q=260%2F1225+m%5E3%2Fsec+%2F%28pi+*+%28%2873%2F2%29mm%29%5E2%29++in+mph%3D&btnG=Search <math>(((260/1 225) (m^3)) / sec) / (pi * (((73 / 2) * mm)^2)) = 113.437141 mph</math>]

=== Effect on Airflow ===

<math>X = \pi (A/2)^2</math>

where (A) is the new MAF Housing diameter in mm. (ex.: 88mm, 90mm, etc.)

<math>Y = \pi (73/2)^2</math>

73mm being the stock MAF Housing size in mm.

Increase in MAF (g/s) in % = <math>((D^2/73^2)-1) 100</math>

{| class="wikitable" style="background:lightgrey"
|+ Various stock MAF housing diameters
! ||MAF|| Diameter || Max airflow || Velocity
|-
|Stock ||S4 ||73mm||220 g/sec||96 mph
|-
|Stock ||RS4 ||83mm||320 g/sec||108 mph
|-
|Chipped ||S4 ||73mm||260 g/sec||113 mph
|-
|VAGCOM limit||RS4||83mm||364.08 g/sec||122 mph
|-
|Stage2+ ||S4 ||73mm||320 g/sec||140 mph
|-
|5V at sensor||S4 ||73mm||364? g/sec||159 mph
|-
|5V at sensor||RS4||83mm||499 g/sec||168 mph
|}

* VAGCOM limit seems to be 318ish on M/T-box, 335ish for M-box, high 320s for A box.
* Sensor value absolute maximums are 364.08 on VAGCOM and 499 on ECUx.
* Note that some programs scale g/sec readings, so what ECUx/VAG-COM reports can't always be trusted.

=== Using the maximum velocity ===

As you can see, the maximum velocity measured by both the Hitachi and Bosch sensors is approximately 160mph. We can use this value to determine what size housing we need to measure a given maximum amount of air mass with a given sensor.

{| class="wikitable" style="background:lightgrey"
|+ Various modded MAF housing diameters
!MAF || Diameter || Velocity || Measured g/sec || True g/sec
|-
|D-Flo ||83mm || rowspan="5" | 160mph ||
|-
|AWE || 84mm* ||
|-
|ASP || 85mm ||
|-
|Custom|| 88mm ||
|-
|ASP || 90mm ||
|}

*AWE actual dimensions are 77mm (inlet) to 100mm at sensor. It reads equivalent to an 82mm-84mm MAF

=== Change in airflow relative to diameter ===

Another way to determine how big a housing to use for a MAF value is by simply using percentages.

{| class="wikitable" style="background:lightgrey"
|+ Various modded MAF housing diameters
!MAF || Diameter || Deviation || Measured g/sec || True g/sec
|-
|D-Flo ||83mm || +29.3% || rowspan="5" | 364 || 471
|-
|AWE ||84mm || ~+30% || 473
|-
|ASP ||85mm || +35.6% || 493
|-
|Custom||88mm || +45.3% || 528
|-
|ASP ||90mm || +52.0% || 553
|}

===MAF and fueling===
* how lemmi fueling (pri/second/accell/decel)
** affects open loop fueling (MAF vs injector duty)
** affects closed loop fueling (LTFTs)
** see also [[Lemmiwinks]].

===Bad MAF===
* Unplugging the MAF will result in the ECU thinking it is broken. Some think this will prevent the ECU from ever going open loop, some think that the ECU can go open loop, but the MAF signal is simply ignored.
* The Audi 2.7t [http://nyet.org/cars/info/Audi_S4_engine_english.pdf self study guide] (page 50) says "If the air mass meter fails, the air mass is calculated on the basis of a [[characteristic curve]] (throttle valve angle and engine speed)"
* Is the [[MAP]] used in "characteristic curve" calculations?
* If so, what does the ECU do in the case where it thinks the MAP is dead?

[[Category:Tuning]]